Cool Misting Systems

Showing 1–24 of 38 results

Low Pressure Switch

$97.00
Low Pressure Switch with 3/8″  inlet/outlet to make sure the pump doesn’t turn on when the water pressure is to

1/2 GPM High Pressure Pump – without Cycling

$1,044.09
This is our most common build, This is a .4 gpm high pressure pump capable of up to 1500 psi. built in pressure regulator, inlet solenoid, gauge, thermal relief valve, 3/8" ptc inlet and 1/4" ptc outlet

1 GPM High Pressure Pump – without Cycling

$1,184.09
This is our most common build, This is a 1.3 gpm high pressure pump capable of up to 1500 psi. built in pressure regulator, inlet solenoid, gauge, thermal relief valve, 3/8" ptc inlet and 1/4" ptc outlet

Pump Cover (Hard)

$60.00
Plastic pump cover will greatly increase the life of your pump, and recommended for ALL installations where the pump will be outdoors in the rain.

Fully Assembled Cycle Timer with Remote

$296.99
Cycle Timer with Remote turns a standard pump that turns Off and On with the power switch, into a Pump

0-4 GPM Regulator

$75.00
Max GPM: 4 Max PSI: 2600 Inlet: 3/8″ F NPT Outlet: 3/8″ M NPT Pump Series: RC Plunger Pumps Features

2 GPM High Pressure Pump – without Cycling

$1,586.09
This is the base pump fully assembled without cycling.  Add the cycling module to allow the pump to be turned

Cycle Timer with Remote

$96.00
Oour remote control works up to 800' away!

1/4 GPM Pump in Case

$895.23
This is our economy pump, .25 gpm, with inlet solenoid, defaults to 3/8" ptc inlet, 1/4" ptc outlet pulse hose required to dampen vibration pressure regulator, pressure gauge, 10' 120v cord (220v version available on request) This pump will Run approximately 12 of the most common #2 (.008") nozzles see our nozzle chart for exact specifications

1/4 GPM High Pressure Pump – without Cycling

$927.09
For a really small job that doesn't want to use much water.

Cycle Timer Remote

$60.00
New for 2014 our remote control works up to 800' away! and controls up to 1.5 hp motors aka 2 gpm pumps!

7 GPM High Pressure Pump – without Cycling

$1,852.09
This is the base pump fully assembled without cycling.  Add the cycling module to allow the pump to be turned

4 GPM High Pressure Pump – without Cycling

$1,802.09
This is the base pump fully assembled without cycling.  Add the cycling module to allow the pump to be turned

3 GPM High Pressure Pump – without Cycling

$1,752.09
This is the base pump fully assembled without cycling.  Add the cycling module to allow the pump to be turned

1/4″ Short Barstock Street Elbow

$4.78
1/4″ MPT x 1/4″ FPT Short BarStock Street Elbow

1/2 HP Motor for Cleaning and Sterilization

$620.00
Motor, Pump, Gauge and fittings for a Cleaning and Sterilization setup.

1/2 HP Motor

$367.00
1/2 horse power motor, 56 C face, 115volt / 208 - 230 volt, comes standard as 115volt special arrangements need to be made for 220v needs, 60hz, Totally Enclosed Fan Cooled, 1800 rpm 4 pole, Draws 8.8 amps at full load 115v and at 220v 4.9-4.4 Amps respectively, keyed shaft 27 lbs, 1.15 service factor, continuous duty cycle, comes with TWO YEAR nameplate warranty longest in the industry! If under reasonable wear and tear motor fails to spin within the first 2 years send us back the nameplate and we will issue you a new motor plus shipping and handling

Brass Regulator

$60.00
This regulator serves as a flow proportionate valve. With this pressure regulating operational regulator valve, you are assured of top

Thermal Relief Valve

$10.00
The TPP140 Thermal Relief Valve Series are mounted into the low pressure side of the pump manifold and will vent